Topcon Hiper GGD L1 L2 GPS GLONASS RTK Base or Rover Receiver

Topcon Hiper GGD L1 L2

Topcon Hiper GGD Receiver Options
GPS
GLONASS
L1
L2
Code Differential Base
Code Differential Rover
RTK Base
Co-Op Tracking
Multipath Reduction
USB Port
Datums Support
Geoid Heigh
DGPS Mode
CMR Output
CMR Input
430-450 MHz Radio Module
Unit Has Been Calibrated By A Topcon Service Center

 

Topcon Hiper GGD GPS GLONASS Receiver
Topcon Positioning System’s HiPer GGD receiver is a dual-frequency, GPS+ receiver built to be the most advanced and compact receiver for the surveying market. The HiPer GGD is a multi-function, multi-purpose receiver intended for precision markets. Precision markets means markets for equipment, subsystems, components and software for surveying, construction, commercial mapping, civil engineering, precision agriculture and land-based construction and agriculture machine control, photogrammetry mapping, hydrographic and any use reasonably related to the foregoing.

The HiPer GGD can receive and process both L1 and L2 signals, improving the accuracy of your survey points and positions. The GPS+ component of HiPer GGD receivers means you can access both the GPS (Global Positioning System) satellites of the United States, and the GLONASS (Global Navigation Satellite System) satellites of the Russian Federation, increasing the number of satellites your receiver can detect, thus improving the accuracy of your survey points, increasing productivity, and reducing cost.

The dual-frequency and GPS+ features of the receiver combines to provide the only real time kinematic (RTK) system accurate for short and long baselines. Several other features, including multipath mitigation and co-op tracking, provide under-canopy and low signal strength reception. The receiver provide the functionality, accuracy, availability, and integrity needed for fast and easy data collection.

Features:

  • GPS + GLONASS Satellites
  • Compact, lightweight design
  • Dual frequency RTK GPS+ (dual constellation) tracking
  • Fully integrated receiver/antenna
  • Internal UHF radio
  • Up to 96Mb of memory

Topcon Hiper

Specifications:

Tracking Specifications
Standard Channels L1 GPS, L1/L2 GPS, L1 GLONASS, L1 GPS + L1 GLONASS, WAAS/EGNOS
Tracked Signals GPS/GLONASS, L1/L2 C/A and P-Code and Carrier, WAAS/EGNOS
Survey Mode Static
Kinematic (Continuous, Stop and Go)
RTK (Real-time Kinematic)
DGPS (Differential GPS)
Survey Accuracy
Static, Fast Static For L1+L2 – H: 3mm + 1ppm x D;
V: 5mm + 1.4ppm x D
For L1 – H: 5mm + 1.5ppm x D;
V: 6mm + 1.5ppm x D
Kinematic For L1+ L2 – H: 10mm + 1.5ppm x D;
V: 20mm + 1.5ppm x D
for L1 – H: 15mm + 1.5ppm x D;
V: 30mm + 1.5ppm x D
RTK For L1+ L2 – H: 10mm + 1.5ppm x D;
V: 20mm + 1.5ppm x D
For L1 – H: 15mm + 1.5ppm x D;
V: 30mm + 1.5ppm x D
Cold Start
Warm Start
Reacquisition
< 60 sec
< 10 sec
< 1 sec
Technology Co-Op tracking
Low signal tracking
Advanced Multipath mitigation
WAAS
Adjustable PLL and DLL parameters
Radio Modem
UHF Radio modem Internal Rx
Data Storage and Display
Status Indicators Four, three-color LED’s and three function keys
Data Features Up to 20 Hz update rate for real time position and
raw data (code and carrier)
10cm code phase and 0.1mm carrier phase precision
RTCM SC104 version 2.1, 2.2, and 2.3 I/O
Multiple Base RTCM
Geoid and Magnetic Variation models
RAIM
Different DATUMs support
Output of grid coordinates
CMR and CMR+ support
I/O
Communication Ports Up to four high speed RS232 serial ports.GGD option also has a USB port.
Connectors External GPS/GLONASS Antenna, Modem Antenna, PWR, USB (GGD option only)
MINTER Four external LEDs ON/OFF control input
Antenna
GPS/GLONASS Antenna Internal
Antenna Type Microstrip
Memory
Internal memory Compact flash card (not removable)
Capacity Standard – 0 MB
Max – 1 GB
Logging Time 53 hours (8 MB, 15sec, L1/L2, 7 satellites)
Logging Interval 0.05 to 85400 seconds, depending on purchased options
Power
Internal battery Li-ion, 3000 mAh, 7.4 V
Battery size 132 x 35 x 18 (mm)
Battery weight 165 g (1 battery)
Number of built-in batteries 2 batteries
Change battery non-detachable battery
Operating Time With UHF PDL Radio ON:
~16 hours (HiPer GD) or ~12 hours (HiPer GGD)
With UHF PDL Radio OFF:
~18 hours (HiPer GD) or ~14 hours (HiPer GGD)
External Power 1 port
Input voltage 6 to 28 V DC (for work)
9 to 28 V DC (for charge battery)
Minimum Charge Current >=2 Amp
Consumption Typical: 2.5W
Maximum: 2.7W
On-board Backup battery for timekeeping and almanac data storage; 10 years minimum operation
Environment
Operating temperature -30 C° to + 60 C° with batteries
Storage temperature -40 C° to +75 C° with batteries
Physical
Enclosure Aluminum extrusion, rainproof
Color Topcon Yellow
Dimensions W:159 x H:88 x D:172 mm
Weight 1.65 kg
Antenna Internal
Battery Two Internal
Controller External
Mounting 5/8-11
Seals Silicon (molding in color)
Keys Three keys:
Power – On/Off
Function (FN) – start/stop data logging; switch
information mode.
Reset – receiver hardware reset
LEDs Four LEDs:
STAT – satellite and receiver status
REC – record and data status
BATT – battery status
RX – modem status
NMEA
NMEA version Ver. 2.1, 2.2, 2.3, 3.0 output
Messages GGA, GLL, GNS, GRS, GSA, GST, GSV, HDT, RMC, VTG, ZDA, ROT
Output interval 1Hz standard; 5, 10, 20Hz optional
DGPS
Correction format RTCM SC104 Ver 2.1, 2.2, and 2.3
RTCM message type 1, 3, 9, 31, 32, 34; user selectable
Process interval 1Hz standard; 5, 10, 20Hz optional
Output interval for RTCM correction data 1Hz standard; 5, 10, 20Hz optional
Elevation mask 0 to 90 deg (independent of data logging)
Multi-base DGPS Differential correction select mode: Nearest, Mix, Best (optional)
RTK
Correction format CMR2/CMR+ (Trimble compatible), RTCM SC104 Ver 2.2 or 2.3
RTCM message type 3, 18, 19, 20, 21, 22; user selectable
Reverse RTK Will be available in future
Ambiguity initialize OTF (L1, L1/L2)
Baseline Length Up to 50km in the morning and evening. Up to 32 km at noon.
Initialize time 5 seconds to 10 min depending on the base line length and multipath conditions
Output interval for CMR/RTCM 1Hz standard; 5, 10, 20Hz optional
Elevation 0 to 90 degrees (independent of data logging)
Solution mode Delay (synchronization)
Extrapolation (not synchronized)
Process interval 1Hz standard; 5, 10, 20Hz optional
Latency Delay mode – 20 msec to 20 sec (depends on latency which receives corrections data from base receiver)
Extrapolation – 20 to 30 msec
Raw Data logging The receiver can record raw data at another interval during RTK operation
Status Fix, Float, DOP, Data Link Status, Modem Latency, Common satellites, Percentage of fixing
Results RTK coordinates, HRMS, VRMS, Covariance Matrix
Ambiguity fixing level Selectable thresholds Low: 95%; Medium: 99.5%; High: 99.9%
Tracking Functions
Multi-path reduction Code and Carrier
PLL/DLL Setting Bandwith, order, adjustable
Co-op tracking loop setting On/Off, Static Mode, Bandwidth of individual PLL, Bandwidth of common PLL
Smoothing interval Code and Carrier
WAAS/EGNOS Standard
Battery Charger (AC Adapter)
Size W:60 x L:112 x H:36 mm
Weight 235 g
Operating Temperature 0 C° to +40 C°
Storage Temperature -40 C° to +85 C°
Input AC 90 to 264 V 1A (110 V AC) 47 to 63 Hz
Output DC 12 V 2.5 A (30 W)
Connector Input (AC): Outlet
Output (DC): Fisher 5 Pin
Battery Charge Time 7 hours for Full Charge
6 hours for 90% Charge

Topcon Hiper GNSS GPS

Topcon Hiper GGD L1 L2 GPS GLONASS Dual Constellation Base Or Rover 430-450 MHz Receiver w/ Options

* Topcon Hiper GGD GPS GLONASS Base Or Rover Receiver [ID- X1081] w/
Options…
– GPS
– GLONASS
– L1
– L2
– Code Differential
Base
– Code Differential
Rover
– RTK Base
– Co-Op Tracking
– Multipath Reduction
– USB Port
– Datums Support
– Geoid Heigh
– DGPS Mode
– CMR Output
– CMR Input
– 430-450 MHz Radio
Module
– Unit Has Been
Calibrated By A Topcon Service Center
* Topcon P/N: 14-008005-03 RS232 Cable
* Antenna
* AC Adapter/Charger
* Power Cord
* User Manual On CD-ROM
* Hard Carrying Case

Buy, Sell, New, Used, Topcon Hiper GGD L1 L2 Price

Topcon Hiper GGD II Spec Sheet