Trimble 5800 GPS Rover 902-928 MHz Receiver

Trimble 5800 GPS Rover

Trimble 5800 GPS Receiver
The Trimble® 5800 GPS receiver provides reliability and simplicity for
basic surveying tasks. You can trust that the proven design of the
Trimble 5800 will perform under the toughest conditions.

Integrated System
Because the Trimble 5800 GPS receiver’s components are completely
integrated, the system is lightweight and ergonomic—and completely
cable-free. 2 MB of internal memory makes collecting data for
postprocessing extremely easy and efficient, whether for static or
kinematic (stop-and-go) surveying.

Advanced Technology
The Trimble 5800 GPS system offers advanced Trimble GPS technology. It
is a 24-channel dual-frequency GPS receiver, containing Trimble’s
proven Maxwell™ technology for robust tracking in difficult GPS
environments.

Two additional channels for WAAS and EGNOS tracking let you perform
real-time differential surveys to GIS grade without a base station.

The dual-frequency Trimble antenna enhances the tracking capabilities
of the Trimble 5800—the patented four-point antenna feed provides
submillimeter phase center stability for precise results. The position
of the UHF radio antenna mounting further increases accuracy by being
out of the GPS line-of-sight, reducing multipath and avoiding
interference with the GPS antenna.

For rover communications use the built-in 450 or 900 MHz radio, or use
an external radio, cell phone or wireless packet data modem.

For extended coverage and comprehensive error checking when roving, the
Trimble 5800 works with signals from multiple base stations
transmitting on the same radio channel. For even larger area coverage,
at highest accuracies, the Trimble 5800 works with Trimble VRS™
networks.

Integrated Bluetooth® wireless technology enables cable-free
communication between the receiver and your Trimble controller.

Trimble 5800

Built For The Field
As a rover, the Trimble 5800 is not only lightweight and cable-free; it
also consumes minimal power. Two miniature batteries will power the
receiver for up to 11 hours – at least enough for a full working day.

Environmentally rated to IPX7, and submersible to a depth of 1 m, the
Trimble 5800 is rugged enough for any job. It can withstand a drop of
up to 2 m on to a hard surface.

Wide Range of Applications:
The 5800 GPS system is ideal for a wide range of positioning
applications, including:

  • Survey
  • Construction
  • Asset management

Features:

  • Purpose-built integrated GPS receiver for improved productivity
  • Scalable from L1, postprocessing to full RTK configurations
  • Lightweight design for reduced fatigue on all-day operations
  • Cable-free rover for more flexibility and ease-of-use in the field
  • Accurate, reliable and rugged

Specifications:

Code differential GPS positioning
Horizontal ±0.25 m +1 ppm RMS
Vertical ±0.50 m +1 ppm RMS
WAAS differential positioning
accuracy
Typically <5m 3DRMS
Static
and FastStatic GPS surveying
Horizontal ±5 mm +0.5 ppm RMS
Vertical ±5 mm +1 ppm RMS
Kinematic
surveying
Horizontal ±10 mm +1 ppm RMS
Vertical ±20 mm +1 ppm RMS
Initialization time Single/Multi-base minimum 10 sec
+0.5 times baseline length in km, up to 30 km
Initialization reliability Typically >99.9%
Physical
Dimensions (WxH) 19 cm (7.5 in) × 10 cm (3.9 in),
including connectors
Weight 1.31 kg (2.89 lb) with internal
battery, internal radio, standard UHF antenna. 3.67 kg (8.09 lb)
entire RTK rover including batteries, range pole, controller and bracket
Temperature
Operating
Storage
–40 °C to +65 °C (–40 °F to +149 °F)
–40 °C to +75 °C (–40 °F to +167 °F)
Humidity 100%, condensing
Water/dustproof IP67 Dustproof, protected from
temporary immersion to depth of 1 m (3.28 ft)
Shock and vibration Tested and meets the following
environmental standards:
Shock Non-operating: Designed to
survive a 2 m (6.6 ft) pole drop onto concrete. Operating: to 40 G, 10
msec, sawtooth
Vibration MIL-STD-810F, FIG.514.5C-1
Electrical
  • Power 11 to 28 V DC external power input with over-voltage
    protection on Port 1 (7-pin Lemo)
  • Rechargeable, removable 7.4 V, 2.4 Ah Lithium-Ion battery
    in
    internal battery compartment. Power consumption is <2.5 W, in RTK
    mode with internal radio
  • Operating times on internal battery: 5.5 hours with 450 MHz
    receive only (varies with temperature)
  • Certification Class B Part 15, 22, 24 FCC certification,
    Canadian FCC, CE Mark approval, and C-tick approval
Communications and Data Storage
  • 3-wire serial (7-pin Lemo) on Port 1. Full RS-232 serial on
    Port 2 (Dsub 9 pin)
  • Fully Integrated, fully sealed internal 450 MHz receiver
  • Fully integrated, fully sealed 2.4 GHz communications port
    (Bluetooth)
  • External cell phone support for GSM/GPRS/CDPD modems for
    RTK and VRS operations
  • Data storage on 2 MB internal memory: 55 hours of raw
    observables based on recording data from 6 satellites at 15 second
    intervals
  • 1 Hz, 2 Hz, 5 Hz, and 10 Hz positioning
  • CMR+, RTCM 2.1, RTCM 2.3, RTCM 3.0, RTCM 3.1 Input and
    Output
  • 16 NMEA outputs, GSOF and RT17 outputs

Trimble 5800 GNSS GPS

Trimble 5800 GPS Rover Receiver 902-928 MHz w/ Options…
– CMR Inputs
– RTCM Inputs
– Data Collector
– Binary Outputs
– 10 Hz Measurements
– Bluetooth
– 902 – 928 MHz Radio P/N: 46454-90
– Authorized By A Trimble Authorized Service Center

* Trimble 5800 GPS Rover Receiver P/N: 45145-90 w/ Options… [ID-
X1386]
– CMR Inputs
– RTCM Inputs
– Data collector
– Binary Outputs
– 10 Hz Measurements
– Bluetooth
– 902 – 928 MHz Radio
P/N: 46454-90
– Serviced By A
Trimble Authorized Service Center
* Li-Ion Battery Charger w/ AC Adapter
* Antenna
* Battery Pack
* RS232 PC Interface Cable
* User Manual On CD-ROM
* Hard Carrying Case

Buy, Sell, New, Used, Trimble 5800 GPS Rover Price

Trimble 5800 GPS Rover III Spec Sheet